Сайт посвящен моему увлечению винтажной аудиотехникой и не является рекламой оказания каких-либо услуг по ремонту
При использовании фотографий с этого сайта просьба не нарушать авторские права

Подписывайтесь: сообщество в Viber, канал в Telegram, профиль в Instagram

В благодарность за создание и поддержание этого сайта угостить кофе можно тут:

Donate PayPal: vrcmlaboratory@gmail.com



25 ноября 2017 г.

Alpage AL-300 - Repair and Adjusting

Вот и пришла очередь привести в порядок очередной аппарат из моей коллекции - Alpage AL-300.
Аппарат довольно сложный в ремонте, сделан практически весь из металла, напрочь отсутствуют электрические разъемы.
UPD. В интернете встретил фотографии этого аппарата с разъемами на ЛПМ, это конечно облегчит обслуживание.
В процессе разборки делал фото, что бы потом можно было подсмотреть если отвалится какой-нибудь проводок.
Эти фотографии можно посмотреть ниже. Надеюсь они кому-либо пригодятся при разборке такого же аппарата, или одного из его клонов.

Размеры пасиков, идлеров и роликов (информация с зарубежных форумов):

The pinch rollers are 8,0mm high (0.315"), the rubber is 6,5mm high (0.256"), the axis diameter is 2,0mm (0.079"), the left roller diameter is 11,0mm (0.43") and the right roller diameter is 13,0mm (0.51").

There is two idlers on the reels that measures 24.5 x 19.0 x 3.0mm (0.965 x 0.75 x 0.12").

What I found on a French audio forum (and my conversions and matching-up using the turntableneedles.com belt info):

Capstan: 251L x 5w x 0.6t = 9.9 inches long = FBM 9.9Counter: 205L x 1w x 1t = 8.0 inches long = SBO 8.0Sub-belt: 162L x 1.3w x 1.3t = 6.4 inches long = SBS 6.4 or perhaps a SBT 6.3

Capstan: 262 x 3w x < 1t = 10.3 inches long = probably a stretched FBS 9.9). Note this belt didn't ride properly centered on the motor hub ... and speed control had to be cranked all the way +ve.
Counter: 210 x <1w x <1t = 8.2 inches long = probably a stretched SBO 8.0
Sub-belt: 166L x >1w x >1t = 6.5 inches long = probably a streched SBS 6.4


What I had in the 'parts bin' that seems to work just fine:

Capstan: FBM 9.6
Counter: SBS 8.0
Sub-belt: SBS 6.2



Провода головок припаяны прямо к дорожкам платы.



Платка автостопа с магнитом и герконом.





Крыльчатка для плавного открытия подкассетника.





Вот так приходилось извращаться, что бы достать тонвалы.


Три идлера.


Головка ALPS.


Усилие подмотки и подтормаживания.


Регулировка параметров по СМ


АЧХ сквозного канала на четырех типах ленты.





Коэффициент детонации.



Спасибо за внимание )



9 комментариев:

  1. С наками какими можно ее сравнить по техническому уровню?

    ОтветитьУдалить
    Ответы
    1. There is something wrong. My Alpage AL300 recording up to 18kHz by level 0 dB on TDK D60.

      Удалить
    2. Is there any confirmation of this? Frequency response charts? It is not physically possible to record tape type I 18 kHz at 0 dB with a linear frequency response of -20 dB. So You have an understated BIAS - and at the level of -20 dB, the frequency response will have a strong rise. Once again, show the frequency response graphs on three levels: -20 dB, -10 dB, 0 dB.

      Удалить
    3. So I am not professional like you and I don't have the equipment to pull down the graphic.I measure with a frequency generator from mini lab and Fluke 115 by 0 dB on the indicators on the deck Alpage AL 300. I am increasing frequency until the level start doping down up to 3 dB by the indicator on the deck and in this point measure the frequency with the Fluke . It shows me 18 kHz on TDK D60. If I do something wrong just let me know. We don't talking here for THD , wave form , clirfactor etc. Ant this deck on normal tape recording any CD with same sound -tape and sorse are identical.

      Удалить
    4. Also how is possible on FeCr to have a worst graphic than on normal tape? May be the Fuji cassette is not gut. Fuji is cheap company. What about Sony FeCr? This what I see is not corresponding to the Quality of Alpage AL300. May be they have some modifications and difference in the models , because I see the head is different than this on my deck and has no sign :Alpage"

      Удалить
    5. I find it difficult to communicate without knowing English. Read the profile forums in your native language - there are answers to all your questions

      Удалить
    6. Вьi можно отвечат по руски. Я понимаю руски но не могу писать и говорить правильно. Я только хочу заметить что АЧХ на FeCr на 0Db не возможно бить только 4500 Hz . Ето не Радуга.

      Удалить
  2. Ето что значить ? Что Нак лешший или Аlpage лепший?

    ОтветитьУдалить